View and Download AMMCO installation instructions manual online. Disc Rotor Lathe. Lathe pdf manual download. iv • AMMCO Brake Lathes. Safety. Safety Notices and. Decals. For your safety, and the safety of others, read and understand all of the safety notices and . Get AMMCO Disc Rotor Lathe Manual. Get all AMMCO manuals!.

Author: Mile Shakataxe
Country: Nepal
Language: English (Spanish)
Genre: Software
Published (Last): 26 April 2005
Pages: 310
PDF File Size: 11.46 Mb
ePub File Size: 15.27 Mb
ISBN: 696-6-70742-857-6
Downloads: 10969
Price: Free* [*Free Regsitration Required]
Uploader: Volkree

Retighten the arbor nut. Turn the cross feed handwheel anmco about a half turn, start the lathe and move the tool bit in to make a second scratch cut.

Important Safety Instructions Safety glasses, goggles, or a face shield contact persons in the area causing personal injury. Read entire manual before installing, operating, or servicing this equipment.

AMMCO Disc Rotor Lathe : Manual

Identify the hazard levels used in this manual with the following definitions and signal words: Page 11 Brake Lathes Cross Feed – The cross feed draws the twin tool bits zmmco the face of a brake rotor when the cross feed drive is engaged. KEEP these and other materials delivered.

Use the outer pulley groove for all passenger car and light truck rotors, Fig. Don’t see a manual you are looking for? Turn each tool bit control the outer knurled knobs clockwise until the tool bits just contact the rotor faces.


AMMCO 7000 Installation Instructions Manual

Turn the left hand tool bit control until the tool bit contacts the rotor surface and makes a scratch cut no deeper than. Page 15 Examine each adapter and the arbor for nicks, burrs, chips, dirt, and amnco. To print the manual completely, please, download it.

Don’t show me this message akmco. Your manual failed to upload Page 14 Brake Lathes 4. Reconditioning Disc Brake Rotors-set-up Fig. Give the rotor a full turn by hand and start the lathe.

Any excessive wear or deformity should be noted and, if not within acceptable limits, the rotor should be replaced.


Safety Notices And Decals For additional copies of either, or further information, contact: Even the smallest nick, scratch, or loose chip can cause incorrect rotor alignment, resulting in inaccurate machining.

Page 7 Brake Lathes Installation Receiving The shipment should be thoroughly inspected as soon as it is received.

Care Of Arbors And Adapters Handle the adapters and arbors with care and store them on individual hooks. Safety Safety Notices and Decals For your safety, and the safety of others, read and understand all of the safety notices and decals included here and on the unit. Don’t have an account? This is caused by runout or wobble due to rotor condition or by the way the rotor is mounted on the arbor.

Use a face shield and dust mask during dusty operations. Page of 20 Go.

TOP Related  ASTM A1038 PDF

Move the tool bits inward until they just contact the faces of the rotor. For additional copies of either, or further information, contact: Refill as necessary with EP gear oil and check the oil level often. When the cross feed has moved the cutting tools all the way across the face of the rotor, the feed will shut off automatically.

Now engage the automatic cross feed by moving the knobFig. Remove all adapters from the arbor after machining a rotor and wipe them clean – especially the inboard adapter. Oiling The lathe is shipped from the factory with the correct amount and type of oil. Spindle Speed – Release the belt tension by moving the V-belt adjusting lever clockwise, Fig. By pressing ‘print’ button you will print only current page.

The cross feed speed control adjusts the feed rate from. Page 19 Brake Lathes Care of Arbors and Adapters CAUTION Although the adapters, arbors, and the spindle are made of top grade steel and are turned, hardened, and precision ground ammmco close tolerances, great care should be taken in their use, handling, and storage.